Bam Bam Bigelow

Credit - PBott

Head Model

---------------

Face 18, Model 18

Figure (0, 0)

Shape (0, 0)

Age (28)

Head (-16, -32)

Eyebrow (0, 22)

Eyes Left (-8, 0), Right (-15, -10)

Nose Left (-26, -11), Right (-22, 0)

Cheek (100)

Mouth (0, 0), Right (-48)

Jaw Left (100, 35), Right (25)

Skin 1, Color 3, Color (-93, 9), Shade (12)

Eyes 15, Color (-100, 9), Shade (0)

Eyebrows 48, Color (-86, 12), Shade (0)

Lips Unpainted

Hair 19, Color (97, 9), Shade (-19)

Facial Hair 72, Color (-99, 9), Shade (0), Trans (100)

Facial Hair 67, Color (-98, 9), Shade (0), Trans (100)

Attire (Order is important. Entrance attire is match attire)

-----------------------

Tights 2, 1, Color (40, -79), Shade (-100), Trans (100), Length (-100)

Wrist Bands (both) 1, 13, Color (-68, 9), Shade (-100), Trans (100), Length (100)

Shoes 1, 1, 1, Color (100, -100), Shade (0), Length (2)

Tattoos (They are not exact, but theyre very close in shape)

------------------------------

Design, Simple, Right Arm, 61, Do not rotate, Enlarge one size up from smallest reduction, place on outside of arm above the elbow. Color (23, 9), Shade (0), Trans (-34)

Design, Simple, Right Arm, 36, Do not rotate, Enlarge one size up from smallest reduction, place on outside of forearm above the wristbands. Color (23, 9), Shade (0), Trans (-34)

Design, Simple, Left Arm, 47, Do not rotate, Enlarge one size up from smallest reduction, place on outside of forearm above the wristbands. Color (23, 9), Shade (0), Trans (-34)

Long Hemline 8, 1, 1, Color (100, -100), Shade (100), Trans (100), Length (3)

Flames on the sleeves

--------------------------

These pictures essentially wrap around the short sleeves of the above shirt.

- Design, Picture, Right Arm, 83, Do not rotate, Enlarge one size up from smallest reduction, place on sleeve so bottom of picture is on edge of sleeve and before the skin, and side of picture is aligned with middle of shoulder. Color (-78, 0), Shade (0), Trans (100)

- It should look like the two pictures have completely wrapped around the arm, however, there will be just a couple of pixels under the arm that are left uncovered. Its up to you if you want to place the following simple design here to cover it up completely. You may want to go into form and set the shoulder width to the maximum so you can see this space.

- Design, Simple, Right Arm, 153, Rotate once, Smallest reduction, place in between the two above pictures so that it covers up the black spot they failed to cover. Color (-85, 71), Shade (0), Trans (100)

- Repeat the above steps to put the flames on the left arm sleeves.

The Three B Logo

----------------------

All of the Bs are Design, Letter, Body, Alphabet 11

- First B - Enlarge three sizes up from smallest reduction.

- Second B Enlarge three sizes up from smallest reduction, Rotate twice so its a mirror image of the first B, place so Bs are connected by the top and bottom edges.

- Third (top) B Enlarge two sizes up from smallest reduction, Rotate three times, place so its centered above the two connected Bs but disconnected them by one pixel(up once on the pad).

- Color (-85, 9), Shade (0), Trans (100)

- It probably wont be centered on the chest when you first enter it. You can center the emblem on the chest by going in and editing through the layer list, which will allow you to move the whole logo as one unit.

Flames on the sides

-----------------------

This isnt an exact science, but its not rocket science either. The idea is to keep the flames symmetrical so the dark half of the picture shows on the front and the bright half shows on the back. You also want to keep the flames connected as they go down the side of the outfit, and you dont want the flames touching the 3B logo. Use my pictures as a guide, but just keep in mind that it doesnt have to be exact, it just has to look good. Since there are 5 designs, you should have enough leeway to adjust a flame upward so that the flow of one into the other looks right. When youre finished, you should be right above the boots.

- There are exactly 5 designs on each side of the outfit going down, but theyre not all the same size. The first three are two sizes up from smallest reduction and mainly on the body, the last two are one size up from smallest reduction and completely on the leg.

- This is the item to be replicated: Design, Tattoo, Body, 32, Color (-83, 9), Shade (0), Trans (100)

- Top most flame, Rotate so that the darker of the two sides is completely facing front, Enlarge two sizes up from smallest reduction, place as far up the chest as it will let you go.

- The flame underneath that, Rotate so that the darker of the two sides is completely facing front, Enlarge two sizes up from smallest reduction, place underneath the previous flame so that it looks like ones flowing into the other.

- The flames underneath that is on the leg, Rotate so that the darker of the two sides is completely facing front, Enlarge ONE size up from smallest reduction, place underneath the previous flame so that it looks like ones flowing into the other.

- The final flame underneath that is on the leg, Rotate so that the darker of the two sides is completely facing front, Enlarge ONE size up from smallest reduction, place underneath the previous flame so that it looks like ones flowing into the other.

- Repeat for the other side of the outfit.

Body Model

Figure Body Morphing (70, 40)

Figure Form:

Head Left (-14, -23), Right (0)

Neck Left (100, 100), Right (-100)

Chest Left (100, 31), Right (5)

Shoulder (both) Left (5, 62), Right (61)

Abdomen Left (100, 72), Right (-14)

Arms (both) Left (74, 79), Right (-52)

Forearms (both) (6, 17)

Hands (both) Left (15, -23), Right (-71)

Waist (63, 62)

Thighs (24, 72)

Legs Left (9, 20), Right (-46)

Feet Left (-29, -7), Right (-43)

Height 63"

(lower of the two 63 settings. I know its not accurate, but this looks more in scale with in-game wrestlers)